1/6/2024 0 Comments Ge z wave smart switch![]() In SmartThings, controls are bare-bones, but note the energy monitor included with both ZigBee units.Ī semi-recessed button on the front of the unit powers the ZigBee outlet: A single press turns the attached lamp on or off. The Jasco smart plug-in dimmer is ginormous compared to Lutron’s Caseta plug-in dimmer-measuring 4 inches wide by 2.5 inches high by 1.5 inches deep-but it won’t block the second outlet when plugged into a two-gang in-wall receptacle. The controlled outlet will accept only two-pronged plugs. Both require grounded, three-prong receptacles, and both are equipped with an always-on three-prong pass-through. lamps with dimmable bulbs), GE offers plug-in dimmers with either Z-Wave or ZigBee capabilities, though the company sent only the former for this review. You can manually control a connected lamp pressing the recessed button on the ZigBee plug-in dimmer.įor impermanent light sources (i.e. GE ZigBee Plug-in Smart Dimmer Jasco Products If you do have a Z-Wave-compatible hub, GE’s Z-Wave dimmer is the better choice of the two. If you don’t already own a smart home hub, but you do have an Echo Plus, you might want to give the ZigBee model a go despite my reservations. (The trick is that this version of the dimmer doesn’t need to any special pairing mode to connect, so SmartThings found it right away.) The only significant difference in operation is that this dimmer does not include an energy-monitoring feature otherwise, everything worked well in my tests.įor whatever reason, Jasco’s list price for the Z-Wave dimmer is $10 less than the list price for its ZigBee model ($44.99 vs $54.99). I paired the device to my SmartThings hub without any trouble. Once installed and paired with your Z-Wave hub of choice (here again, the instructions are frustratingly confusing), the switch operates in the same fashion as the ZigBee model (read my review above for details). We tested Jasco’s GE smart lighting products by enrolling them to a Samsung Smart Things hub. That said, the manual included with this product is slightly different, but even more scattered and confusing. The hardware installation process was also very nearly the same. The Z-Wave Plus version of Jasco’s GE Smart Dimmer is virtually identical to the ZigBee version, including requiring the presence of a neutral wire and GE add-on switches for multi-pole installations (up to five). GE In-Wall Z-Wave Plus Smart Dimmer Jasco ProductsĪ small LED at the bottom right-hand corner of both GE smart switches glows when the dimmer is turned off, to help you locate it in a dark room (the Z-Wave Plus model is shown here). You can’t turn the LED off (unless you turn the switch on), but it’s small enough that you could cover it with a bit of white tape if it bothers you. ![]() A small LED on the bottom right-hand side of the dimmer will help you locate it in the dark. I also saw considerable flicker using an older LED bulb, but a newer one transitioned smoothly. There are no indicators of overall brightness (such as the LEDs on Wemo’s superior W-Fi dimmer), and the dimming action can be slow. Jasco Productsīoth of the GE in-wall smart switches have screw terminals and backstabs as opposed to flyaway electrical leads (the ZigBee model is shown here). Pressing and holding the top or bottom of the toggle will brighten or dim the light respectively (it’s compatible with dimmable LED, CFL, incandescent, and halogen bulbs). Instead, you tap the top part of the switch to turn the light on, and tap the bottom to turn it off. You’ll soon discover that it does not move much at all. ![]() You’ll need to either purchase a rocker-style plate separately or re-use the one you have if you’re replacing a switch of the same style.Īctually, the switch only looks like a rocker. Be advised, however, that the box includes both white- and almond-colored paddles, but it does not include a wall plate. That said, with a little patience (or a lot of experience), everything should go together without too many surprises. The instructions aren’t just hard to read, they’re actively confusing. The installation guide includes an oversized diagram of a typical old-school switch (which you’re removing), but only a tiny diagram of the new switch (which you’re installing). Unfortunately, the installation instructions included with the device are far from acceptable, and if you don’t have prior experience with these types of devices, they might do more harm than good. There’s nothing terribly unique about the wiring and installation process, though the recessed ground wire is a bit difficult to access.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |